DSC IMPASSA INSTALLATION MANUAL PDF

Quick Links. See also: Programming Manual. Self-Contained Wireless. This manual contains information on limitations regarding product use and.

Author:Yojin Gubei
Country:Peru
Language:English (Spanish)
Genre:Science
Published (Last):3 December 2004
Pages:329
PDF File Size:11.63 Mb
ePub File Size:2.37 Mb
ISBN:470-9-88411-725-1
Downloads:38335
Price:Free* [*Free Regsitration Required]
Uploader:Dojind



Quick Links. See also: User Manual. Table of Contents. Self Contained Wireless Alarm System. The entire manual.

The entire manual should be carefully read. Page 4: Safety Instructions For Service Personnel Safety Instructions for Service Personnel Warning: When using equipment connected to the telephone network, always follow the basic safety instructions provided with this product. Save these instructions for future reference.

Inform the end-user of the safety precautions that must be observed when operat- ing this equipment. Smoke Detectors Research indicates that all hostile fires in homes generate smoke to a greater or lesser extent. Detectable quantities of smoke precede detectable levels of heat in most cases. Page 6: Limited Warranty Limited Warranty Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in Items Not Covered by Warranty materials and workmanship under normal use.

During the warranty period, Digital Security Controls shall, at its option, repair or replace any defective In addition to the items which void the Warranty, the following items shall not be covered by Warranty: i freight cost to the repair centre; Page 7: Introduction Refer to the associated installation guide for information on program- G Armed: Panel is armed.

Mounting Figure Opening Cover If required, separate the front and back covers by removing the cover screw then inserting a small slotted screwdriver between the front and back covers and gently twist the screwdriver to separate. If upgrading the battery 60Hz. This is done to ensure that, if consistent good placement test results are generated with reduced sensitivity, the product should have more than adequate range when placement test exits and the sensitivity level returns to normal.

The Ready light must be on to arm the system. If the Ready light is off, ensure all protected doors and windows are secure or bypassed. To arm in Away mode, press and hold the Away function key for 2 seconds or enter a valid user code and leave the premises through a door programmed as Delay. If any zones are programmed as Night Zones zone definition 37 pressing [ ][1] will activate the Night mode instead of Away mode.

All display lights and LCD pixels turn on. Press [ ] to exit Template Programming. Page Advanced Programming Advanced Programming Advanced Programming How to Program To help reduce programming time and eliminate errors, fill in the Programming Worksheet with the required programming defaults before programming the system.

To enter Installer Programming, press [,][8][Installer Code]. Programming Option cont. To program attributes 9 to 16, press 9 within the zone attribute section. Press 9 again to program attributes 1 to 8. Zone Attribute Defaults Attribute: 2-way All others are ignored. In the restored state, the panel is disarmed.

Violation of the zone arms the panel. Tampers and faults begin their associated trouble sequence. If the system is armed with this keyswitch and then disarmed by another method, the keyswitch zone must be restored and then violated before the system can be armed with this zone again. This zone definition ensures an alarm condition persists by looking for a second alarm transmission or the absence of an alarm restoral condition.

The output de-acti- vates when all of the selected Troubles are restored. Hardwired Zone 33 Input is enabled. The zone definition is programmed in the first entry of section []. Zone supervision is determined by attributes 14, 15, and 16 programmed in section []. Pressing and holding the fire key for 2 seconds generates a fire alarm. The keypad sounds a set of 3 beeps to acknowledge the valid alarm and the buzzer sounds a pulsing alarm tone for the length of the bell time-out, or until an access code is entered.

Keypad backlighting is continuously on. Keypad backlighting is never on. The keypad displays the temperature received from the lowest numbered external siren. If the local clock display is also enabled, then the keypad displays date, time, and temperature. If [] is programmed when using the Police Code feature, the panel generates a Police Code event if any two zones go into alarm during an armed-to-armed period.

Zone alarms transmit to the System Test Transmission Call Direction when they are being transmitted as part of the walk test enabled if section [] option [2] is ON. Page 61 Programming Descriptions Exit Fault If an Exit Error occurs and entry delay expires before the system is disarmed, this reporting code is sent. If the delay zone that caused the exit error has cross zoning enabled, the exit fault and zone alarm still transmit if a second zone is not violated.

Valid entries: [] to []. Program data [] to disable shutdown. When the Opening After Alarm reporting code is successfully trans- mitted to a programmed telephone number, the keypad sounds a series of 8 beeps to confirm to the end user that the Opening After Alarm Code was sent and received.

Phone number 4 backs-up phone number 3 if phone number 3 fails to communi- cate FTC. Phone number 4 communicates in the same format as phone number 3. OFF: Phone number 4 is Independent. Phone number 4 does NOT back up phone number 3. Events are communicated to phone number 4 if enabled in Communicator Call Direction, section []-[] , using the communicator format pro- grammed in section [].

Program the phone number as required. ON: Force Dialing Enabled. The system dials regardless of the presence of dial tone after the first attempt. The wire- less supervisory window is calculated by multiplying the programmed value by 15 minutes. Valid entries are 04 to 96 which correlates to 1 to 24 hours.

The siren activates for trouble beep conditions. Trouble beeps are sounded until any key on the keypad is pressed or until all trouble conditions are restored.

This is intended for indoor sirens, but not outdoor sirens or sirens that are mounted in a sleeping area. Scroll to the second line to view. If the SIM card is activated, the second line displays and the signal strength bars. To access enter [,][] from Installer Programming. Enter digits 1 to 5 to select a function key F1-F5 for programming.

Key in a 2-digit entry to assign a function to the key. The system returns to the key selection screen in section [].

Default labels are in English and do not change when an alternate language is selected. Pressing and holding the Fire key for 2 seconds sends a fire key alarm request to the panel. Page Alarm. An installation location with a sustained signal level of two or more bars is recommended. Page Power Up Connect battery leads to the battery. Plug the panel power transformer into the AC outlet. Page Enroll Alarm. However, if the phone test was initiated via the [3] key, or through the Interactive Ser- vices menu, the siren will not sound.

Set to ON for the session to be initiated by the operator. Set to OFF for the session to begin immediately after the siren turns off. Zone Attributes Sections [] through [] control the attributes for each zone. Page Troubleshooting: Module Status Information Troubleshooting: Module Status Information Module status information for verifying and troubleshooting the module connection status or errors can be found through the Interactive Services menus on the Impassa.

To access these, See the following table for potential module states. Make sure the device being added is powered up and within 3 to 6 feet of the Impassa panel. Page Specifications Refer to the Home Automation installation instructions and guides on the Alarm.

Specifications Table Specifications Compatibility Impassa panels with software versions 1. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. See Programming Sections []-[] for Reporting Codes. Contact ID The first digit in parentheses is automatically sent by the control.

The second two digits are programmed to indicate specific information about the sig- nal. This allows the central station to communi- cate with the occupants through the microphone and speaker of the alarm system. Caution Call Waiting Cancel Section [], Option 4 feature on a non-Call Waiting line will prevent successful communication to the supervising station. All Rights Reserved. The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries].

Any misuse of the trademarks is strictly prohibited and Tyco International Ltd.

GASTRONOMIA NOVOANDINA PDF

Product Manuals

.

CAPNOGRAFIA Y OXIMETRIA PDF

DSC Impassa - Quick Install Guide

.

AN INTRODUCTORY DICTIONARY OF LACANIAN PSYCHOANALYSIS PDF

Impassa SCW9055-433 Installation Manual

.

Related Articles